Image Header Info

Call Us: +86 15051969118

E-mail:sale@itcpowerworld.com
Image Header Info

Mon - Fri 09:00 - 22:00

Sat - Sun 09:00 - 22:00

Blog

Installation Method Of Diesel Generator Portable Mobile Light Tower

Installation Method Of Diesel Generator Portable Mobile Light Tower

Hello everyone, we are a manufacturer – ITCPOWER.

The generator adopts our self-developed brand, with four 100W LED lamp holders or four 1000W halogen lamp high-efficiency energy-saving lamp holders.

According to the needs of the scene, each lamp head can be independently adjusted and rotated at a large angle up and down, left and right to achieve 360° omnidirectional lighting.

The lamp head can also be evenly distributed on the lamp panel to illuminate in four different directions. If four lamp heads are required to illuminate in the same direction, the lamp panel can be turned over within 250° to the opening direction as a whole according to the required illuminance and orientation, and the cylinder is used as the axis to rotate 360° left and right; the overall lighting takes into account the distance and brightness of the lighting High and wide.

★The 3-section telescopic cylinder is used as the lifting adjustment method, and the lifting height is 4.3; turning the lamp head up and down can adjust the beam irradiation angle, and the light coverage radius reaches 45-65 meters.

★The generator set can be used for power supply directly, or it can be connected to 220V mains for long-term lighting; when the generator set is used to supply power, the continuous working time can be up to 13 hours when it is filled with fuel once.

★The opening and closing of each light and the lifting of the gas rod can be controlled separately within 50 meters by wireless remote control, and the lifting and lowering of the telescopic gas rod can be quickly controlled by using an electric or manual air pump.

★The lamp panel, cylinder and generator set are integral structures. The bottom of the generator set is equipped with a universal wheel with a brake device, which can run on uneven roads and railroad tracks, and rail wheels can also be added.

★The whole is made of high-quality imported metal materials, with compact structure and stable performance, ensuring normal work in various harsh environments and climatic conditions. The anti-rain, water spray, and wind resistance level is 8. The surface is electrostatically sprayed and has corrosion resistance. it is good.

★In order to meet the individual needs of users, if the standard configuration of this product cannot meet the needs of the user’s work, our company can adjust the number of lamp caps, power, floodlight or spotlight of the lamp panel, the lifting height of the telescopic cylinder and the configuration of the generator. Make adjustments according to user requirements.

★In order to meet the individual needs of users, if the standard configuration of this product cannot meet the needs of the user’s work, our company can adjust the number of lamp caps, power, floodlight or spotlight of the lamp panel, the lifting height of the telescopic cylinder and the configuration of the generator. Make adjustments according to user requirements.

Installation method of diesel generator mobile light tower

Instructions

  1. Install the U-shaped bracket

Open the side door of the vehicle body, and remove the hexagon socket head cap screws on the mounting position at the rear of the vehicle body. Erect the U-shaped bracket at the installation position at the rear of the vehicle body, and the positioning pin of the U-shaped bracket is located on the left side. Fix the U-shaped bracket to the rear of the car body with the socket head cap screws.

  1. Install the tow bar

Push up the front of the vehicle body with the support, and then open the side door of the vehicle body. Use a wrench to unscrew the bolts that fix the L-shaped bracket inside the car body, and then pull out the L-shaped bracket. Insert the tow bar into the car body, fix it inside the car body with bolts, then lower the front support feet, adjust the support feet to a suitable height, and then insert the fixing pins. Take out the chain inside the car, hang it on the iron rings at both ends of the car bottom, and then hook the hook of the tow bar with the chain; then remove the support.

  1. Support feet after installation

Unplug the pins that fix the rear support feet on both sides of the rear of the carriage, pull out the support feet to a suitable position, and then insert the fixing pins. Shake the rocker to adjust the height of the rear support feet so that the wheels are off the ground and the weight of the car body falls on the support feet.

  1. Install the light tower lifting pole

Lift the lighthouse lifting rod to the top of the car body and place it in the U-shaped bracket, ensuring that the latch in the U-shaped bracket is inserted into the positioning hole on the lifting rod. Introduce the six-core cable and the four-core cable on the lift rod into the car body through the large and small Glen joints on the car body respectively, and connect the cables according to the diagram, pay attention to the one-to-one correspondence between the cables; pay attention to the installation Put on the packing and tighten the Glen joint to ensure the sealing effect. When installing two cables, pay attention to leaving a margin of 15-20CM outside the car body to prevent the cables from being stressed when the lifting rod is lifted.

  1. Install the wire rope

Remove the two positioning pins on the pulley at the front end of the vehicle body and the pulley and positioning pins at the front end of the lift rod. Pass the wire rope on the winch in the car body through the square hole at the bottom of the car body at the position of the pulley, pull it out from the lower groove of the pulley, then bypass the pulley removed from the front of the lifting rod, and install the pulley at the front end of the lifting rod. Then pull the wire rope back to the upper hole of the pulley at the bottom of the car body and fix the wire rope with a pin. Pay attention to ensure that the front end of the wire rope is facing the direction of the chuck, and ensure that it is in a clamped state and cannot be loosened. Install the pin at the upper hole of the pulley at the front of the lift rod to prevent the wire rope on the pulley from falling off.

  1. Install the lamp head

Unscrew the bolts that fix the lamp heads on the beam at the top of the lift rod; then adjust the mounting brackets of the four lamp heads to a horizontal position. Fix the four lamp heads on the beam in turn. Connect the input cables of the four lamp heads to the junction box at the top of the lift rod, and connect the wires according to the requirements in the illustration; pay attention to the wiring sequence of the four lamp heads.

  1. Pull out all the cross bars until the positioning pins are automatically inserted, and prop up the support feet so that the support feet are firmly in contact with the ground to resist strong winds.

Note: If the horizontal bar is not fully unfolded or the supporting feet are not firmly in contact with the ground, it is strictly forbidden to raise the light pole. If the supporting feet are damaged or defective, they should be replaced. Spread the weight and lower the pole height if the wind is strong, the pole bar tipping over could result in serious injury or even death.

  1. Loosen the bolts on the lever bracket, shake the winch on the tow bar until the light pole is upright, and then lock the safety latch at the bottom of the light pole.
  2. Start the flood light, generator, and run the lighthouse lighting function.

A、Check the position of the diesel engine and oil and the water in the water tank. If the oil tank is empty, please drain the air in the oil pipe. Please refer to the operation manual for starting the diesel engine.

Note: Please check if all ground wires are connected well, special safety measures, hit the ground wire rod, and firmly connect the ground wire to the rod and the frame.

B、Before starting the diesel engine, make sure that the air switch is in the OFF position, turn the electric door lock to the starting position, the controller is powered on, and the diesel engine can be started by pressing the start button on the controller until the diesel engine runs smoothly.

C、Press the main circuit breaker (the main control switch of the light fixture) to the ON position.

D、Press all circuit breakers (control switches of lamps) to the ON position respectively until all lamps are on. The starting time of the lamp is about 5-10 minutes, which is a gas discharge lamp metal halide lamp.